Slitting Clearance Explained: Calculation, Reference Values by Material and Burr Diagnosis

Burr is the most common and most frustrating quality problem in metal slitting. It spoils the appearance of the product, and it can also throw off downstream stamping dimensions, scratch equipment and injure operators.

The first reaction in many plants is to change the knives. The more fundamental cause is often incorrect clearance. In TOA DR Enterprise's experience servicing slitting tooling, many edge quality problems can be solved by setting the clearance correctly, without replacing the knives right away.

This article explains what clearance is, how to calculate it, reference starting values by material, and how to trace a problem back to its cause from the burr pattern. For the on-line procedure, see How to Set Slitting Clearance.


What Is Slitting Clearance?

Slitting clearance is the horizontal gap between the upper and lower knives, expressed as a percentage of material thickness.

Two parameters are easily confused:

  • Horizontal clearance: the lateral distance between the cutting faces of the upper and lower knife — the core parameter for shear quality
  • Vertical penetration (overlap): how far the upper knife goes below the top of the lower knife — it controls where shearing starts

Vertically the knives overlap (penetration); horizontally they are apart (clearance). Together the two decide how the material is sheared in the stack.

How Shearing Works

As material enters the stack, the upper and lower knives press on it from either side of the cut line. Under the combined compressive and tensile stress, the material fractures across a weak section.

The clearance determines the quality of that fracture:

  • Too small: the shear zone is too narrow, the material is forced into secondary shearing, and the result is fragmented burr and faster knife wear
  • Too large: the shear zone is too wide, the material is stretched and torn rather than cut cleanly, and the result is a full, continuous burr
  • Correct: the material fractures cleanly at the lowest cutting force, with a smooth cut face and minimal burr

Calculating Horizontal Clearance

Basic Formula

Horizontal gap (each cut) = Material thickness × Clearance percentage

Example: 1.5 mm 304 stainless falls in the 1.5–4.0 mm row (6–9%). At 8%:

Horizontal gap = 1.5 mm × 0.08 = 0.12 mm

The clearance calculator does this conversion for you.

Reference Values by Material

These are the reference starting values used across slitter.ai, by material and thickness:

MaterialThickness (mm)Single-side clearance (recommended reference values)
Mild steel (cold rolled)0.3–0.85–8%
Mild steel (cold rolled)0.8–27–10%
Mild steel (cold rolled)2–49–12%
Stainless steel (304/316)0.3–1.54–7%
Stainless steel (304/316)1.5–46–9%
Aluminum0.5–26–10%
Copper and brass0.3–1.55–8%
High-strength low-alloy steel (HSLA)AnyMild steel of the same thickness +1–2%
Advanced high-strength steel (AHSS)AnyMild steel of the same thickness +2–4%
Galvanized steelAnyBase metal of the same thickness +0.5–1%
Silicon steel (electrical steel)Any4–6%

Data version: 2026-11 · Updated 2026-11-09 · Reference values: use them as a starting point and confirm by test slitting. Slitting Clearance Data Table

For materials not in the table, such as hot-rolled steel, martensitic stainless (420/440) and UHSS, start from the closest material and confirm by test slitting.

Important: these are starting values. The best clearance depends on knife wear, batch hardness, machine rigidity and line speed. Test-slit at the recommended value, then fine-tune.


Setting Penetration

Penetration and horizontal clearance must both be right for the best edge.

Material thicknessRecommended penetration
Under 0.5 mm0.05–0.15 mm
0.5–1.5 mm0.10–0.30 mm
1.5–4 mm0.25–0.80 mm
4–8 mm0.5–1.5 mm
Over 8 mm1.0–2.5 mm

Effects of Wrong Penetration

Too little:

  • The material is not fully sheared; it tears apart instead
  • Rough edges and longitudinal drag marks on the strip

Too much:

  • Cutting force rises sharply, and so does drive current
  • Knives deflect, the stack loses rigidity and cut widths become uneven
  • Carbide knives may chip

Material-Specific Considerations

Stainless Steel

Work hardening is the key challenge with stainless. In austenitic grades (304/316), the material around the shear zone hardens quickly during cutting and forms a layer harder than the base metal.

This means:

  • Set stainless clearance from the data table and confirm the extent of the work-hardened layer by test slitting
  • Keep knives sharp, so edge wear does not widen the shear zone

Electrical (Silicon) Steel

Clearance on electrical steel directly affects magnetic performance. Too much clearance leaves a larger work-hardened zone at the cut, which reduces permeability; a poor cut face also makes poor contact when laminations are stacked, losing magnetic performance.

Electrical steel slitting requires:

  • Tight clearance control — the reference value is 4–6%
  • Carbide knives — HSS wears too fast, and the effective clearance drifts quickly as it wears
  • Regular burr measurement, with a regrind once burr exceeds 5 μm

High-Strength Steel (AHSS/UHSS)

The tensile strength of high-strength steel can exceed 1,500 MPa, which affects slitting in several ways:

  • Cutting force is far higher than for ordinary carbon steel, so the arbors must be stiffer
  • Springback is large, so the effective clearance is smaller than the setting — a reference approach is to add +2–4% to the clearance for mild steel of the same thickness
  • After setting clearance, verify the actual knife gap with a dial indicator instead of relying on the spacer calculation

Diagnosing Seven Burr Patterns

Each burr pattern points to a different root cause. Recognizing the pattern is the fastest route to the fix.

Pattern 1: Full, continuous burr on every strip

Signs: even burr height, smooth root, continuous along the edge Diagnosis: horizontal clearance too large Fix: reduce clearance toward the low end of the recommended range and test-slit

Pattern 2: Fragmented, whisker-like burr on every strip

Signs: broken burr in short whiskers, with a bright band on the cut face Diagnosis: horizontal clearance too small, or severely worn knives Fix: increase clearance, and check whether the knives need regrinding

Pattern 3: Odd and even strips differ

Signs: strips 1, 3, 5… have large burr while 2, 4, 6… are fine, or the reverse Diagnosis: the first datum position on the arbor has shifted, or the upper and lower arbors are not parallel Fix: re-establish the arbor datum; measure the parallelism of the upper and lower arbors

Pattern 4: The two edges of a strip differ

Signs: one edge of the strip has large burr and the other is fine, repeated on every strip Diagnosis: uneven clearance on a particular knife pair, or uneven wear on the two side faces of a knife Fix: re-measure and re-adjust the spacers for that pair; check the flatness of the knife side faces

Pattern 5: Burr rises and falls along the strip

Signs: burr height varies periodically along the coil length Diagnosis: excessive arbor runout, or a local chip on a knife Fix: measure arbor runout with a dial indicator and check it is within 0.003 mm

Pattern 6: Burr grows through the coil

Signs: burr is acceptable at the start, then grows through the middle and end of the coil Diagnosis: normal knife wear — the effective clearance grows as the edge wears Fix: record knife life and set a planned knife change and regrinding cycle

Pattern 7: Edge wave after slitting

Signs: the strip edge is wavy rather than straight Diagnosis: too little penetration, or incorrect clearance letting the strip spring back and deform after the stack Fix: increase penetration moderately; check that recoiler tension is even


Optimizing Clearance Systematically

For a new material or knife combination, run a clearance sensitivity test:

Step 1: Establish a Baseline

Use the middle of the recommended range as the baseline. Slit at least 50 m and sample burr height, rollover depth and cut-face finish.

Step 2: Step the Clearance

Change the clearance in steps of ±10% of the baseline, test-slitting and sampling at each step. Example for 1.5 mm stainless with a 0.12 mm baseline:

Test pointHorizontal gapPurpose
Baseline −20%0.096 mmSee how too small behaves
Baseline −10%0.108 mmLower boundary
Baseline0.120 mmBaseline data
Baseline +10%0.132 mmUpper boundary
Baseline +20%0.144 mmSee how too large behaves

Step 3: Find the Optimum

Compare burr height, cutting force (drive current) and rollover depth across the test points. The clearance range with the lowest burr and a reasonable cutting force becomes the production setting for this material.


How Spacer Accuracy Affects Clearance

Clearance does not exist on its own — it is set by the thickness accuracy of the spacers.

With spacers of ±0.01 mm tolerance, the actual clearance can vary by more than 0.02 mm from one assembly to the next. On 1.5 mm stainless, a 0.02 mm change equals 1.3% of the material thickness — well within the sensitive range.

Conclusion: clearance optimization only repeats reliably on precision spacers. Use spacers with a tolerance of ±0.002 mm or better, and check the actual clearance with a dial indicator after each assembly.


Quality Measurements

Burr Height

Acceptable burr height depends on the end use, and the customer's specification takes precedence. Common limits:

End useMaximum burr height
General structural and construction steel≤ 12%
Automotive stampings≤ 8%
Motor and transformer laminations≤ 5%
Battery electrodes≤ 2%

Data version: 2026-11 · Updated 2026-11-09 · Reference values: use them as a starting point and confirm by test slitting. Slitting Clearance Data Table

Rollover Depth

Rollover is how far the material bends down before it separates. It should be below 15% of material thickness for general work and below 10% for precision parts such as motor laminations.

If rollover is clearly too large, check the clearance setting and knife wear first.

Burnish Ratio

From top to bottom, the cut face shows a burnished (sheared) band and then a fracture band. The share of the burnished band reflects shear quality:

  • Normal: burnished band 40–70% of the cut face height
  • Clearance too large: burnished band under 20%, mostly fracture
  • Clearance too small: burnished band over 85%, with a secondary shear band

FAQ

Q: Still getting burr at the recommended setting? Check actual spacer thickness and arbor runout first, then adjust from the recommended value in ±0.01 mm steps. Recommended values are starting points.

Q: Burr is hard to control on AHSS? AHSS springs back, so the effective clearance is smaller than the setting. A reference approach is to add +2–4% to the mild steel clearance for the same thickness, with precision spacers and carbide knives.

Q: Burr grows partway through a coil? Normal knife wear makes the effective clearance drift. Set a planned knife change cycle.

Q: Penetration or horizontal clearance — which matters more? Horizontal clearance has the more direct effect on edge quality. Set it first.


See also: Slitter Knives · Arbor Spacer Complete Guide · Slitting Defects · Tooling Installation